Apogee TS-100 Uživatelský manuál Strana 16
- Strana / 19
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
16
TROUBLESHOOTING AND CUSTOMER SUPPORT
Independent Verification of Functionality:
Apogee ST-110 temperature sensors yield a resistance proportional to temperature. A quick and easy
check of sensor functionality can be accomplished with an ohmmeter. Connect the lead wires of the
ohmmeter to the black and red wires from the sensor. The resistance should read 10 k (10,000 ohms) at
25 C. If the sensor temperature is less than 25 C, the resistance will be higher. If the sensor temperature is
greater than 25 C, the resistance will be lower. Connect the lead wires of the ohmmeter to the black and
blue wires from the sensor. The resistance should read 24.9 k, and should not vary. Connect the lead
wires of the ohmmeter to the red and blue wires from the sensor. The resistance should be the sum of the
resistances measured across the black and red wires, and black and blue wires (e.g., 10 k plus 24.9 k at
25 C).
Apogee ST-300 temperature sensors yield a resistance proportional to temperature. A quick and easy
check of sensor functionality can be accomplished with an ohmmeter. Connect the lead wires of the
ohmmeter to the red/black (red and black are connected internally, without a resistor between them;
continuity between red and black indicates both wires are functional) and white wires from the sensor.
The resistance should read 100 (0.1 k) at 0 C. If the sensor temperature is less than 0 C, the resistance
will be lower. If the sensor temperature is greater than 0 C, the resistance will be higher. Connect the lead
wires of the ohmmeter to the red/black and orange wires from the sensor. The resistance should read 10
k, and should not vary. Connect the lead wires of the ohmmeter to the orange and white wires from the
sensor. The resistance should be the sum of the resistances measured across the red/black and white
wires, and red/black and orange wires (e.g., 100 plus 10 k at 0 C).
A quick and easy check of fan functionality can be determined using a DC power supply. Power the fan
with 12 V DC by connecting the positive voltage signal to the red wire from the fan and the negative (or
common) to the black wire from the fan. When powered, the fan blades should spin. Make sure to keep
fingers clear of blades before connecting fan to 12 V DC.
Compatible Measurement Devices (Dataloggers/Controllers/Meters):
Measurement of ST-110 thermistor resistance requires an input excitation voltage, where 2.5 V DC is
recommended. Measurement of ST-300 PRT resistance also requires an input excitation voltage, where
2.1 V DC is recommended. A compatible measurement device should have the capability to supply the
necessary voltage for the specific sensor.
The sensitivity (mV output from thermistor per C) of the temperature measurement from the ST-110
thermistor varies with the excitation voltage, and varies as a function of temperature. With an excitation
voltage of 2.5 V DC, the sensitivity is lowest near the ends of the measurement range, -50 and 70 C. A
compatible measurement device (e.g., datalogger or controller) should have resolution of at least 0.6 mV,
in order to produce temperature resolution of less than 0.1 C across the entire temperature measurement
range (less than 0.05 C from -35 to 45 C).
The sensitivity (mV output from PRT per C) of the temperature measurement from the ST-300 PRT is
approximately constant across the entire measurement range. With an excitation voltage of 2.1 V DC, a
Související produkty a manuály pro Měření, testování a kontrola Apogee TS-100
(12 stránky)Bosch SMD50E12CH manuals
Owner’s manuals and user’s guides for Dishwashers Bosch SMD50E12CH.
We providing 1 pdf manuals Bosch SMD50E12CH for download free by document types: Instruction Manual
Komentáře k této Příručce